Profile for novline plastic windows. The best profiles for plastic windows - review, reviews, recommendations. What is a quality profile

Car mats have long been an attribute of comfort in the car, without them it is difficult to imagine a modern vehicle. This accessory performs many functions: it prevents moisture from entering the body, which reduces the likelihood of corrosion, the floor is less dirty and easier to clean. In addition, car mats contribute to a certain extent to reduce noise in the car, making driving less tiring, and creating a feeling of cleanliness and comfort.

3 main requirements for good car mats:

The car mat must be fixed on the floor of the car, excluding moving around the cabin or trunk while driving. If the accessory does not meet this requirement, it does not protect well from moisture and dirt, interferes with the driver and passengers, especially when getting on and off, getting underfoot. A badly fastened driver's mat can become a source of danger, because. when moving, it shifts forward and creates an obstacle to the movements of the control pedals.
The car mat must have a non-slip surface.. This is especially important for the driver: his foot should not slip when moving from one pedal to another.
Car mats should be made from environmentally friendly materials, guaranteeing the absence of harmful substances and odors in the cabin.

Types of car mats

The car mats that you can buy from us are made from different materials, which determines the differences in their properties and price. You can choose the type of accessories that suits you best:

Rubber

Manufacturers offer floor mats for cars in two types:

Universal models are suitable for all makes and models of cars. Such accessories have an enlarged format and a simplified form. They are marked over the entire area with notches, cutting along which, the dimensions of the product can be adjusted for a variety of machines. Universal car mats can be bought at a lower price, since their cost is lower. However, this merit is reverse side: none of these products fits perfectly in size and profile to any vehicle, and after trimming appearance spoils.

Model car mats are custom-designed for a specific car model of a certain year of manufacture, thanks to which the accessories exactly match the floor configuration. Their advantage is a perfect fit to the surface of the cabin or trunk.

Model products dominate the domestic market: they perform their functions much better than universal ones, and manufacturers, focusing on demand, offer accessories of various materials and colors for almost all makes and models of cars. Our store has a wide range of such mats, and you are sure to find the right one for your car!

Standard of Germany

Novoline window profiles are produced with a mounting width of 58 mm and 70 mm. 58 mm window systems suggest a four-chamber design. The location of the cameras inside the profile prevents the process of freezing of the window structure.

Specifications Novoline_58mm.

Profile width - 58mm.
Profile chambers: frame-4, sash-4, impost-3.
Frost resistance up to - 55 s
Profile corresponds to class A
Seal - black, grey.

araks56.ru

Profile Novoline green | sar-okno64.ru

More than ever, today's market demands a profile that meets European standards, at the same time having an affordable price. Such an inexpensive and high-quality profile is Novoline Green (Novoline).

Profile quality for plastic windows.

The NOVOLINE profile system belongs to class A, the plastic formulation used for its manufacture was developed by specialists from IKA (Germany), thanks to which Novoline complies with German thermal insulation standards.

In the manufacture, only primary raw materials are used, and also in the mixture formulation there are specially developed in the USA (Rohm & Haas) modifiers of impact strength.

The protective film for the profile is made in Germany.

Novoline window profile marking.

Each running meter of the profile has a laser marking with the name, date of production and the corresponding GOST.

Construction and appearance.

Structurally and externally, NOVOLINE is a complete analogue of the well-known German KBE profile. Technical excellence is combined with an elegant design.

The operational properties of the profile.

Novoline behaves well in harsh conditions. natural conditions Russia, the entire line of profiles has certificates for frost resistance, the profile does not turn yellow over time, it is resistant to ultraviolet radiation.

Types of Novoline profiles:

There are two types of Novoline profile system, with an installation depth of 58 mm and 70 mm.

Specifications profile NOVOLINE (Novoline) 58 mm:

Mounting depth 58 mm.
The maximum width of a double-glazed window is 32 mm.
The number of cameras in the profile -3.
Frost resistance - up to -55 degrees Celsius.
Class A
Service life - more than 40 years.
Gray or black seals.
Heat transfer resistance, m2°C/W - 0.7.
Environmentally friendly PVC

Technical characteristics of NOVOLINE (Novoline) 70 mm:

Mounting depth - 70 mm.
The maximum double-glazed window is 42mm.
The number of cameras is 5.
Frost resistance - up to -55оС.
Heat transfer resistance, m2°C/W - 0.83.
Service life - more than 40 years.
Gray or black seals.

Environmentally friendly PVC profile.

By purchasing windows from the NOVOLINE profile (Novoline) in the First Window Company of Saratov. You get European-level windows at a very affordable price!

sar-okno64.ru

NOVOLINE | IP Barinov "Stroy project"

NOVOLINE - The system of plastic profiles "NOVOLINE" is a complete analogue of the profile of the German brand "KBE", which allows you not to buy new equipment for processing the profile (To start working, you only need to reconfigure the existing one).

Plastic windows are made of PVC (Polyvinyl chloride) - durable, economical and environmentally friendly material. It is quite convenient and reliable, and thanks to special technologies, PVC profiles are the best alternative to the traditional wooden frame today and surpass it in many ways. NOVOLINE PVC profile is produced on high-tech lines the largest plant in Russia, equipped with the most modern extrusion equipment from Germany, each meter of the profile is laser marked with the time of production, the name of the system and the GOST number. The unique qualities of the plastic are provided by the original mixture formula specially selected with the participation of specialists from IKA (Germany). All necessary additives used in our recipe are imported. They contain: impact modifier (Rohm&Haas, USA), calcium carbonate (Omya, France), titanium dioxide (DuPont, USA).

NOVOLINE profile accessible to everyone

stroi-proekt-rb.ru

Plastic windows in Orsk at low prices

The Tenkoff company manufactures and installs modern plastic windows from Rehau (Rehau), Novoline (Novoline) profiles. The profile systems used have proven themselves well in the Russian climate, have a high coefficient of heat preservation, protection from street noise, and durability.

High performance characteristics of our windows are ensured by fittings of Russian and European production.

In the production of our windows, we use energy-saving glass, which allows you to better keep warm in the house in winter, and protect you from heat in summer.

Rehau windows

The Rehau 60 mm profile is perhaps the most popular in Russia today.

Reliable windows made of such a profile effectively retain heat, protect the house from street noise and easily fit into any interior.

Specifications

System depth/number of chambers: 60 mm/3 chambers.
Heat engineering: Ropr =0.70m2°C/W.
Burglar-proof: installation of reinforced locking devices due to a 13 mm offset of the tool groove axis.
Air and watertight: Reliable protection against drafts, dust and water thanks to two sealing circuits (6/8 mm seal overlap inside and outside).
Surface: high quality, perfectly smooth, easy to clean.

NOVOLINE WINDOWS

Profile Novoline 58 mm Russian production perfect for the harsh climate of Russia. The manufacturing plant is located in Samara. The relative proximity to Orsk makes it possible to reduce the cost of the window due to the low cost of transporting the profile.

This profile has a class A certificate. In the manufacture of the profile, only primary raw materials are used. The recipe for the NOVOLINE profile was developed with the participation of specialists from IKA (Germany), thanks to which it meets modern German standards for heat savings. Extruded on the latest high-tech equipment and equipped with a protective film made in Germany.

Profile specifications

Profile width - 58mm.
Possible thickness of a double-glazed window - 32 mm
Profile chambers: frame - 4 chambers, sash - 4 chambers, impost - 3 chambers.
Frost resistance up to - 55 s
The profile corresponds to class A.
Seal - black, grey.

xn----7sbqbggqdwl4b2aa2ixa.xn--p1ai

Novoline - WINDOWS MASTER

The Novoline plastic profile is similar to the German KBE system. Window profile "Novoline" is intended for the manufacture of plastic door and window systems installed in any buildings located in difficult climatic zones.

The Novoline window profile was designed taking into account Russian climatic conditions. It is characterized by high resistance to frost and resistance to ultraviolet radiation. The profile "Novoline" is made from a material with a high coefficient of resistance to heat transfer, a low coefficient of thermal linear expansion. Welded seams of profiles possess the increased durability. Profile "Novoline" has frost resistance.

The NOVOLINE window profile is manufactured using the latest German extrusion equipment. High-tech production lines ensure the production of the highest quality window profile, as evidenced by the presence of a laser marking on each meter, informing about the date of production, the number of the state standard and the name of the system. The German company IKA participated in the creation of a PVC mixture with unique technical characteristics. Special prescription components that give special strength to plastics are produced at foreign chemical enterprises (United States of America, France). Novoline window profiles are produced with a mounting width of 58 mm and 70 mm. 58 mm window systems assume a four-chamber design. The location of the cameras inside the profile prevents the process of freezing of the window structure.

The width of the five-chamber profile is 70 millimeters. Installation consequence additional camera- sound insulation and thermal insulation increase by 30 percent. Premises where windows from this profile are installed are reliably protected from low temperatures. And the increased thickness of the walls of the profile prevents the freezing of the window structure, the formation of water condensate. In addition - perfect combination elegance, technical solutions and economic benefits.

Specifications Novoline_58mm.1. Profile width - 58mm.2. The possible thickness of the double-glazed window is 32 mm3. Profile chambers: frame-4, sash-4, impost-3. 4. Frost resistance up to - 55 s5. The profile corresponds to class A.6. Seal - black, grey.

oknamaster02.ru

NOVOLINE

In recent years, many people who want to order a window are looking for a window from a profile that will meet all modern standards and at the same time be affordable. It is for such customers that the NOVOLINE profile line was created.

The system of plastic profiles "NOVOLINE" is a complete analogue of the profile of the German brand "KBE", which allows you not to buy new equipment for profile processing (To start working, you only need to reconfigure the existing one).

The NOVOLINE profile system is designed for the manufacture of windows and doors for any premises and is specially adapted to Russian operating conditions.

The NOVOLINE system profile formulation was originally developed for the harsh Russian climate. Therefore, the main attention in the development was paid to achieving high frost resistance, UV resistance, strength welds, low coefficient of linear expansion and high coefficient of resistance to heat transfer. All NOVOLINE profiles are certified as frost-resistant profiles.

PVC profile "NOVOLINE" is produced on high-tech lines of the largest plant in Russia, equipped with the most modern extrusion equipment from Germany, each meter of the profile is laser marked with the production time, system name and GOST number. The unique qualities of the plastic are provided by the original mixture formula specially selected with the participation of specialists from IKA (Germany). All necessary additives used in our recipe are imported. They contain: impact resistance modifier (Rohm&Haas, USA), calcium carbonate (Omya, France).

High quality window constructions created on the basis of the profile new system"NOVOLINE" made it possible to establish the latest quality criteria, one of which is the technical characteristics.

All profiles of the NOVOLINE 58mm system have three internal chambers. With this design and arrangement of the chambers, the profile does not freeze through. The flow of heat through the metal is excluded, since the metal reinforcing profile is located in the middle chamber, located between two small chambers, and does not come into contact with the outer walls of the profile anywhere.

The 5-chamber NOVOLINE profile has an installation width of 70 mm, which allows you to optimally keep the heat and silence in the room.

Products made from NOVOLINE PVC profiles combine an elegant appearance, as well as technically and economically advantageous solutions.

stand-art-saratov.ru

In recent years, many people who want to order a window are looking for a window from a profile that will meet all modern standards and at the same time be affordable. It is for such clients that the line of profiles " NOVOLINE».

Plastic profile system « NOVOLINE» is a complete analogue of the profile of the German brand « KBE», which allows you not to buy new equipment for profile processing (To get started, you only need to reconfigure the existing one).

Profile system " NOVOLINE» is designed for the manufacture of windows and doors for any premises and is specially adapted to Russian operating conditions.

Recipe profile systems " NOVOLINE» was originally developed for the harsh Russian climate. Therefore, the focus during development was on achieving high frost resistance, UV resistance, weld strength, low coefficient of linear expansion and high coefficient of heat transfer resistance. All profiles NOVOLINE» are certified as frost-resistant profiles.

PVC profile " NOVOLINE» is produced on high-tech lines of the largest plant in Russia, equipped with the most modern extrusion equipment from Germany, each meter of the profile is laser marked with the time of production, the name of the system and the GOST number. The unique qualities of the plastic are provided by the original mixture formula specially selected with the participation of specialists from IKA (Germany). All necessary additives used in our recipe are imported. They contain: impact resistance modifier (Rohm&Haas, USA), calcium carbonate (Omya, France).

The high quality of window constructions created on the basis of the profile of the new system " NOVOLINE» made it possible to establish the latest quality criteria, one of which is the technical characteristics.

All system profiles NOVOLINE» 58mm have three inner chambers. With this design and arrangement of the chambers, the profile does not freeze through. The flow of heat through the metal is excluded, since the metal reinforcing profile is located in the middle chamber, located between two small chambers, and does not come into contact with the outer walls of the profile anywhere.

5-chamber profile " NOVOLINE» has an installation width of 70 mm, which allows you to optimally keep the heat and silence in the room.

In products made from PVC profiles " NOVOLINE» combines an elegant appearance, as well as technically and cost-effective solutions.

I am glad to welcome my readers!

During my work, I installed many windows, but most often the quality was not very good.

The fact is that the main thing in a plastic window is the profile, but at first glance, all windows look the same. That is why, I often encountered the fact that customers choose a low-quality profile.

What is the main thing in plastic windows? The basis of plastic windows is a profile. A good profile is a guarantee of high-quality and reliable plastic windows.

How to choose a quality profile and what to look for when choosing? I want to help you find the answer to this question in this article.

We go outside or take a newspaper and what we see are the windows of KBE, REHAU, VEKA, SALAMAHDER, LG, PROPLEX, BRUSBOX and the like. What is behind all these names? - These are the names of window profile manufacturers and nothing else, and your windows will be made by completely different companies, and we know perfectly well what our manufacturers can make from the best raw materials.

And yet a little about the profile manufacturers. When ordering windows, you will hear from the manager that windows (for example, KBE, VEKA, REHAU, SALAMANDER) are German windows made in Germany - naturally the best and highest quality. What is true in these words and what is not? Of all those listed, only SALAMANDER is 100% produced abroad (therefore, it has a corresponding price), the rest have long been produced in Russia.

And about the production of the window profile. Most profile manufacturers have built their factories in Russia. I was at the KBE and VEKA factories - excellent factories, imported equipment, foreign specialists, imported raw materials, so there is not much difference from where the profile comes from (I think the situation is similar at other factories of European manufacturers).

True, as always, there is a "BUT". This is a "BUT" profile system produced specifically for Russia, i.e. it is not used abroad - it is only for us at "our request". The advantage of this system is cheap, the disadvantage is to reduce the cost, the profile walls make thinner, respectively, the thermal resistance is less, the strength is less.

For the south, this is quite acceptable, in the middle lane - it is doubtful, in the north they can freeze. Usually this profile system is called an object profile and is used for glazing large objects - multi-storey residential buildings, industrial enterprises etc. There are also Russian and Turkish systems, but since we are going to glaze our house, we will not consider these systems in detail.

Which profile I personally prefer, I can write further.

Which profile do you think is better? What is better Rehau or Brusbox? Veka or Proplex? KBE or LG? etc.

The most difficult and annoying question, to which it is almost impossible to give a reasoned answer, I can only express my personal opinion. I emphasize once again - this is my personal opinion, and not advertising, and the conversation will only focus on the profile systems with which I worked.

A few words about SALAMANDER (goes to non-competition) – good profile. The main advantage is made in Germany, the main disadvantage is that it is expensive. It would have been produced in Russia - it was among the middle peasants.

Now, in order about the profile systems produced in Russia:

Better than others in:

number of customer reviews
the number of defects in the supply of plastic profiles,
sealant,
holding seminars, trainings and training courses for window manufacturers.
Variety of profile systems.

Another advantage is that it sells the profile only to well-equipped enterprises for the production of plastic windows, which it regularly checks and issues its certificate to these plants. Therefore, if you have chosen a factory working with this profile, then the likelihood of getting into an unpleasant situation is less.

I give second place. This company sells its profile only to well-equipped plastic window manufacturing plants, which it regularly checks and issues its certificate to these plants. Therefore, if you have chosen a factory working with this profile, then the likelihood of getting into an unpleasant situation is less.

Deserved 3rd place.

Flaws:

There are disruptions in the supply of the profile, the rejection of the profile is more often than - for REHAU and VEKA
Sells a profile to any factories of plastic windows.

THYSSEN, LG, DIMEX

MOTNTBLANK, PROPLESS, BRUBEBOX

They share the last place by the number of positive reviews of people who installed windows, but they are very well suited for glazing balconies and loggias, as well as domestic premises. Advantage - low price.

P.S. I have not worked with other profile systems, so I can’t say anything about them.

source: http://infokna.narod.ru/

What profile of a plastic window is better to choose? Selection tips and manufacturer rating

The profile is the main element of any window; the durability and reliability of the entire structure depends on it. At first glance, the profile for PVC windows from different manufacturers looks almost the same.

The difference in quality becomes apparent after several months (or even years!) of use, when cheap windows begin to warp and cracks form in them. How to choose a good plastic profile for windows? How are products of different brands different from each other? And does it make sense to save on glazing by choosing an economy class profile?

Profile for PVC windows: characteristics and types

The profile is the basis of the entire structure, from which window sashes and frames are made. They determine not only the appearance of the window, but also its strength. Common materials for window profiles are wood (cedar and larch) and aluminum.

But most often the profile for windows is made of PVC, or polyvinyl chloride. Such a profile is reinforced with metal inserts and has air cavities inside, which increase the thermal insulation of the structure.

According to the European standard EN 12608 SR "Unplasticized polyvinyl chloride (PVC-U) for the manufacture of windows and doors" and similar Russian GOST 30673-99 "Polyvinyl chloride profiles for window and door blocks. Specifications» profiles are classified according to a number of characteristics. In particular, in terms of the thickness of the outer and inner walls, the following are distinguished:

Class A profiles - have outer walls with a thickness of 2.8 mm and inner walls with a thickness of 2.5 mm; they provide the best thermal insulation and are considered the best choice.
Class B profiles - have outer walls with a thickness of 2.5 mm, internal - from 2.0 mm; such windows are not only “colder”, but also 15% less resistant to deformation.
Class C profiles - all others that do not fit the standards A and B, they are not subject to strict requirements.

Note!

There is a so-called "objective" profile, which is designed for installation in non-residential industrial premises. It cannot be used in houses and apartments - because of the thin walls, it does not hold heat and is unstable to deformation.

At first glance, such a profile is no different from the usual one - except that you can see the object marking on the protective film. Often unscrupulous companies offering very low prices for their product, they sell windows from such a profile.

Choosing the best profile for plastic windows

It is not easy to determine "by eye" which profile of plastic windows is better, but there are some features that can say a lot about its quality.

Profile uniformity

The plastic must be homogeneous and absolutely smooth. The grainy surface suggests that the windows were most likely made in artisanal conditions and are fake. The coating must also be uniform, free of streaks and gradients.

By the way. In order not to buy a fake at the price of branded windows, pay attention to the factory markings on the inside of the window box. It should be stamped with the name of the manufacturer and a number of numbers: shift number, devices for the production of PVC profiles and date of manufacture.

Profile width

Most often, companies offer a plastic profile for windows with a width of 58 mm - this is a classic option, preferred for residential premises. There is also a profile with a width of 70 mm, this is often installed in high-rise buildings or where the climate is especially harsh. The 90 mm wide profile belongs to the premium class, it is characterized by excellent heat and sound insulation characteristics. However, not all companies work with such products.

Profile thickness

The thickness of the profile should be the same, from 2.5 mm to 3 mm. However, thin walls are not suitable for heavy window blocks - in this case, the welding seam is less durable, which means that the reliability of the entire structure suffers.

Number of air chambers

The number of cameras also depends on the width of the profile. A 58 mm profile can have a maximum of three chambers - which, however, is quite enough for the windows to retain heat. 70mm - three, four and even five cameras. The last of those mentioned (70 mm) are most in demand for glazing apartments and houses.

The norm for a 90 mm profile is six chambers. The more cameras, the warmer and quieter it will be in the house. However, in fairness it should be said that the difference between, for example, a three- and four-chamber package is not so significant.

Number of double-glazed windows

Do not confuse the number of air chambers in PVC profile with the number of double-glazed windows. A double-glazed window is several sheets of glass interconnected along the contour using a special frame and sealants. Airtight chambers with air or other gas inside are formed between the panes.

A single-chamber double-glazed window is the lightest, it consists of two glasses and one air chamber between them. Such double-glazed windows are very light, suitable for glazing large openings, so they are often installed on balconies, loggias and terraces. However, they are not suitable for windows due to insufficient thermal insulation.

For a house, cottage, office or apartment, it is better to choose a double-glazed window consisting of three sheets of glass and two air chambers. Three-pane double-glazed windows made of four sheets of glass are not common, they are heavy and let in less light than other types of double-glazed windows.

Such windows are in demand only in the North, where the temperature in winter can drop to -40 o C and lower. At higher temperatures, there is almost no difference between two- and three-chamber double-glazed windows.

Useful advice!

When choosing a plastic profile for windows, pay attention to the frame seals. There should be two of them, otherwise condensation will settle under the frame, and this spoils the insulation and creates a favorable environment for bacteria and mold.

Window profile rating: comparison of products from key manufacturers

rehau
One of the most famous companies, which has been producing reliable windows for more than half a century and is considered the main innovator in this area - Rehau engineers are constantly improving the design and configuration of the profile - so the company pays great attention to environmental friendliness and energy-saving technologies. The company produces a profile with a width of 60-70 mm. Rehau products belong to the middle class.
VEKA
Another German "giant", whose products are valued all over the world. VEKA produces white and colored profiles that do not fade or turn yellow when exposed to direct sunlight. The seal is made of natural rubber, which does not freeze even under the influence of very low temperatures - a valuable quality for the Russian climate. The line includes models with a width of 58 to 90 mm. In terms of price, VEKA windows are comparable to Rehau.
Trocal
This is a company with a long history, one of the pioneers in the production of plastic windows. The first model was released in 1954. For decorative finishing, the company offers the widest range of options - from lamination to acrylic coating. The profile is produced using the environmentally friendly Greenline technology and provides perfect thermal insulation. Profile width - 70 mm.
Salamander
This German company is not as well known as KBE or VEKA, but Salamander products are in no way inferior to them in quality. The profile is produced exclusively in Germany, which means that by purchasing such windows, you can count on truly European quality - at the same European price. The company produces bags with a width of 60 to 76 mm.
KBE
One of the most popular German brands that produces environmentally friendly windows recommended for installation in children's institutions and hospitals. KBE windows are of high quality and durability (they can serve up to 50 years!), and the line includes both luxury models and economy options. Profile width - from 58 to 70 mm.
Proplex
Proplex- Russian company, which, despite its youth, has already managed to establish a wide production and significantly modernize window systems. The profile is developed with the participation of Austrian specialists and taking into account Russian conditions. At very good quality The company's products still manage to maintain affordable prices. Proplex offers models in widths from 58mm to 127mm.

This is only a small part of the manufacturers of plastic windows, in fact there are dozens, if not hundreds. What plastic windows are better? When choosing glazing, you should give preference to well-known brands, but be sure to check all the documentation - famous brands are often faked. Branded windows at too low a price are a sign that they may be trying to deceive you.

Editorial opinion

Even the best windows will not last long if mistakes were made during their installation. Better simple economy class windows installed by professionals than expensive German windows installed by amateurs.

source: http://www.kp.ru/

Which profile of plastic windows is better

What is a quality profile?

A guarantee of quality and durability plastic window is a quality profile. Even if at first glance the entire profile for plastic windows is the same, in reality this is far from being the case. What profile for plastic windows is better, and how to choose the right window, experts from VEKA Rus advise you.

Certificates

The entire profile from which the windows are made is certified. The most significant is the RAL Certificate, which certifies not only the type of product, but also the place of its production. In other words, a profile of the same brand, but manufactured at different factories, will not always have this certificate.

Management System Certificate ISO quality 9001:2000 is issued to industries that have a well-organized management system in compliance with all technological, economic and organizational requirements that are typical for the production of developed countries. Both Russian VEKA plants have this certificate.

If the profile is wider, is it more reliable and warmer?

Profile width is one of its main characteristics. Many window manufacturers promise a couple of extra millimeters to the profile width in their advertising campaigns but are they really useful?

The following offers are most often found on the market:

classic profile 58 mm;
profile 70 mm with increased installation width;
profile VEKA ALPHALINE 90 mm.

The width of 58 mm is due to the "classics of the genre" - wooden frames, which were replaced by plastic windows. Today, the EUROLINE 58 mm profile allows the production of modern warm windows that meet the requirements of most customers in different climatic zones. Properly manufactured and installed, this is the best window profile for any room.

A profile with a width of 70 mm is a proposal that appeared in the 80s of the last century. Having higher heat-saving soundproofing characteristics, this profile is especially fond of Russian consumers. In the product group of VEKA profiles, SOFTLINE, SWINGLINE and PROLINE have a width of 70 mm.

The 90 mm wide profile is a premium product that appeared about 5 years ago. The VEKA ALPHALINE profile allows the use of double-glazed windows up to 50 mm thick and is currently the unsurpassed leader among window profiles with enhanced energy-saving characteristics.

Note!

The choice of profile width largely depends on the installation location (window in the office, vestibule door, front door to the store, windows in a country house) and climate.

Now another novelty has appeared on the market - the SOFTLINE 82 profile. The innovative multi-chamber system, elegant style and the choice of more than 40 modifications guarantee the satisfaction of the most demanding customer. The SOFTLINE 82 system provides the best insulating performance, is fully compatible with 70 mm profiles and can be installed in any home.

Number of cameras

The second characteristic of the window is the number of cameras in the profile. There are three in the standard. The first one is for condensate drainage, the second one is for placing a reinforcing metal insert, and the third one is for fixing parts of the fittings and creating an additional air gap for better window tightness. The number of chambers depends on the width of the profile. So, a 58 mm profile can have a maximum of three cameras, but a 70 mm profile - preferably four. For a profile of 90 mm, the norm is 6 cameras.

Three and six chamber profile systems

Increasing the number of cameras with the same profile width does not significantly change the characteristics of the window. To improve the heat-saving characteristics, more wide profile, and not more partitions in it.

Full package

Another important point- double glazing. The number of glasses in the window affects its characteristics and cost. Double glazing is the most common, but single glazing or triple glazing can also be ordered.

"Triple" windows are warmer. However, they weigh more and require high-quality assembly and stable construction. Single glazing is the coldest. It can be used for glazing unheated balconies, as well as summer houses. Double glazing is optimal for technical specifications, and allows you to maintain indoor comfort all year round.

Profile class

There are two classes of metal-plastic profiles. The first, class A, with a thickened outer wall, is certified by the RAL system as the optimal profile for windows, doors and frame glazing.

Useful advice!

The second, class B, is a lightweight profile with a thinner outer wall, the so-called "object" profile. It has a slightly lower cost, but does not guarantee the preservation of the characteristics of the window throughout its operation.

Windows from the "object" profile, as an economical option, can be offered by absolutely all manufacturers, but you must remember that such a window may have weaker corner joints, poorer dimensional stability, lower energy-saving characteristics, the risk of premature wear of fittings, shorter service life.

conclusions

Summing up the reasoning on the topic of choosing a profile for a metal-plastic window, we emphasize:

The presence of certificates confirms the quality.
According to the mounting width, all profiles are divided into two main classes: 58, 64 mm and 70 -76 mm. Within the class, the thermal characteristics are the same. A profile with a width of 68 mm and a profile with a width of 72 mm do not differ from each other.
The number of cameras affects the window quality only if the profile belongs to different width classes.
The most common is double glazing.
Class A profile is the leader in reliability and quality.

When choosing windows, be able to hear the necessary information and filter out ads. The quality of your windows depends on your choice. Take the time to make the right choice!